Product Description

The MHU75NG is a propane fired, forced air convection heater. This unit is ideal when ceiling heights do not allow for infrared heaters to be used. It easily installs from the ceiling with included angle brackets. Unit has power exhaust which allows for both vertical or horizontal venting. Unit is thermostatically controlled and includes a spark ignition system with self diagnostic control module. This CSA certified heater will heat up to 1,000 square feet and comes with a three year limited warranty on the parts and the burner and a ten year warranty on the heat exchanger.

---

Product Details

• Amazon Sales Rank: #389619 in Home
• Size: mr heather 31'x28"x22' vent 38"x28"x7' thermostat 6"x4"x3"
• Color: Silver
• Brand: Mr. Heater
• Model: F260775
• Number of items: 1
• Dimensions: .0" h x .0" w x .0" l, 95.00 pounds

Features

• Efficient and effective convection heat for up to 1,100 sq. ft.
• Attractive low profile design
• Easily installs from ceiling
• Power exhaust allows for vertical or horizontal venting
• Features self-diagnostic control module

---

Customer Reviews

Most helpful customer reviews

25 of 25 people found the following review helpful.
Heater nice. Installation was work!
By Toolman
Ordered the propane model to put up in a Morton Building workshop. Package arrived quickly with minimal damage to outside cardboard box. Nice unit and fairly easy to lift (I am 6' 190 lbs. average jock) but recommend two people to lift in place on ladder or other device.

Things to consider for installation: Installed two joist between trusses in the attic to hang the unit from (time consuming). Venting horizontal is easier but I perfer vertical. Think this process out. This unit requires a 4" exhaust vent. I went through a metal roof and used a Dektite on 4" double wall exhaust pipe. Make sure you have the appropriate tools, fasteners and sealers before starting this part of the project. Hooking the exhaust vent to the unit should be well planned too. It is not easy and you should have the exhaust vent pieces you plan to use to take some rough measurements prior to fit up. I hung the unit using threaded rod on C channel so I could adjust the unit up or down, si de to side, and back to front (I used 19" center to center from side to side, could use 20" too). The brackets in the kit require a small amount of grinding to avoid the strain relief on the blower fan and if you use the top 1/2" knockout on the back of the unit for electrical connections. Electrical connections are easy. The unit has two 1/2" knockouts on back for electrical connections. I used 16-3 cord for power and 18-2 (solid) for the thermostat. I have it on a 15 amp circuit breaker. Use a strain relief for the power cord. The gas pipe connection is 1/2" female. I already had propane gas pipe in the shop. I used various elbows, cross, and 1/2" pipe lengths for initial plumbing. A union was used for the final connection. Exhaust vent was connected first and then the gas pipe was fitted. It is easier to make adjustments to the gas pipe than the exhaust venting. Once all connections were checked, the unit powered up, the appropriate green light flashed on the circuit boar d and the unit fired right up.

The only problem with the heater involved the two top burners were allowing flame to reach and burn the section between the heat tubes. A call to technical support (30 to 45 minute wait on a Monday) stated to pinch the two pieces of metal that form the burner closer together in the area involved which solved the problem. This would not please the average joe. It involved removing 6 screws that hold the panel that the circuit board is on and 4 screws that hold the two burners in place. It took me two time to get it right. I didn't mind as I like to tinker and I have an above average selection of tools.

The unit is quiet for a forced air heater. It works great and heats up my 1800 square foot workshop quickly. It took two weeks of various evenings and weekends at a leisurely pace to get it installed. This review is being written two weeks after installation so no comments on longevity. Good luck!

18 of 18 people found the following review helpful.
Good performance. Some poor workmanship.
By PR2000
I purchased this heater to heat my 1100 square foot garage/shop in California. Although the weather here is generally mild, it does get down to about 20 degF in the winter months. The heater easily heats the shop up quickly and keeps it warm. I mounted the heater to my 10 foot ceiling by installing two lengths of predrilled angle iron to the ceiling and hanging four 5/16" all thread rods with a hook on one end. I attached the all thread at the four corners of the heater and then lifted the heater and hung it from the angle iron by passing the hooked ends of the all thread through holes in the angle iron.

My only complaint about this product is poor workmanship in assembly. When I opened the box, I found several of the screws which were supposed to hold the fan protection cover in place laying in the bottom of the box. I was able to find all of the missing screws and nuts and install them correctly. There was also damage to some of the sheet metal on the unit structure that occurred during shipping. I was able to straighten out the metal and avoid a return.

8 of 8 people found the following review helpful.
Great garage heater! It does the job very well!
By Doc Martin
I purchased this heater in October 2009 and had it professionally installed. It works perfectly and heats my oversized two-car garage with no problem whatsoever in a North Dakota winter. I wouldn't recommend buying the Mr. Heater thermostat however. The one I purchased with the heater was defective out of the box and was cheaply made. I bought a Honeywell CT87K locally and it worked just fine until today when it failed and made the heater run continuously even though it was set as low as it could go. I'll never buy another Honeywell thermostat as they won't warranty it without the proof of purchase (not what the owner's manual says at all).

I highly recommend this heater!